Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
What're your thoughts about How to Install a Bathtub Yourself?
Setting up a bathtub isn't specifically rocket science, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately challenging task. If the old bathtub is readily accessible, the task can move easily; if you have to open a wall surface to eliminate the old tub as well as place the new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to move out the old bathtub as well as set in the new one. Make sure you have certified on your own for the work and are comfortable trying it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This article will certainly help you install a new bathtub in your restroom if you have already bought a brand-new tub and also do not require to transform the setup of your previous water supply pipelines.
Your devices as well as material checklist should comprise the following:
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water supply. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipes. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washers are in place in between the faucet and the sink. Secure the tap in position with the producer supplied backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind must be connected to the faucet ends first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the called for position. The wooden boards are valuable in equally spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little points.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bathtub up until the spirit level reads level.
To install faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water system and check all joints as well as new pipework for leakages and also tighten them if required. Fill the bathtub and also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Ultimately, repair the bath paneling as explained in the supplier's instruction manual. Tiling as well as sealing around the tub ought to wait up until the bathtub has actually been made use of at the very least once as this will settle it into its final placement.
Planning for the Installation
First of all, the supporting framework provided with the bathroom must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the taps device to avoid strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be fitted in its last position.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to split a rigid seal, triggering the water to permeate the wall in between the bath and also the tiling, resulting in problems with moisture and possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill the tub with water before sealing, to enable the activity experienced when the bathtub remains in usage. The sealant can split rather early if you do not take into account this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise conveniently offered on the market. It is suggested to fit the tiles using waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our article about A Step-by-Step Guide to Installing a Bathtub. Thanks a lot for finding the time to browse our post. If you enjoyed our blog posting plz remember to share it. I praise you for your time. Kindly come visit our site back soon.
Tailored emergency solutions; call now. Report this page